https://forum.lavalink.com/ Sat, 18 Apr 2026 07:06:03 +0000 MyBB https://forum.lavalink.com/showthread.php?tid=20454 Fri, 15 Jun 2012 19:39:58 +0000 admin]]> https://forum.lavalink.com/showthread.php?tid=20454 http://lavalink.com/2012/06/pos-to-nvr-i...on-part-2/ that details how to make the necessary connections.]]> http://lavalink.com/2012/06/pos-to-nvr-i...on-part-2/ that details how to make the necessary connections.]]> https://forum.lavalink.com/showthread.php?tid=5775 Thu, 09 Feb 2012 16:20:54 +0000 admin]]> https://forum.lavalink.com/showthread.php?tid=5775
Baud rate, parity, stop bits, etc are all easily translated.

http://lavalink.com/2011/12/using-the-et...converter/]]>
Baud rate, parity, stop bits, etc are all easily translated.

http://lavalink.com/2011/12/using-the-et...converter/]]> https://forum.lavalink.com/showthread.php?tid=5773 Thu, 09 Feb 2012 16:16:52 +0000 admin]]> https://forum.lavalink.com/showthread.php?tid=5773
http://lavalink.com/2011/12/rs-232-remot...levisions/

peek inside an LG TV and you might find Linux. Access commands and features not available in the stock consumer interface. And control your TV over your home network using a LAVA Ether-Serial Link.]]>
http://lavalink.com/2011/12/rs-232-remot...levisions/

peek inside an LG TV and you might find Linux. Access commands and features not available in the stock consumer interface. And control your TV over your home network using a LAVA Ether-Serial Link.]]> https://forum.lavalink.com/showthread.php?tid=5771 Thu, 09 Feb 2012 16:12:07 +0000 admin]]> https://forum.lavalink.com/showthread.php?tid=5771
http://lavalink.com/2011/12/piping-dos-over-ethernet/]]>
http://lavalink.com/2011/12/piping-dos-over-ethernet/]]> https://forum.lavalink.com/showthread.php?tid=5770 Thu, 09 Feb 2012 16:09:34 +0000 admin]]> https://forum.lavalink.com/showthread.php?tid=5770
The schematic for the parallel port portion of this chip is here:

http://lavalink.com/2011/12/an-inside-lo...allel-pci/]]>
The schematic for the parallel port portion of this chip is here:

http://lavalink.com/2011/12/an-inside-lo...allel-pci/]]> https://forum.lavalink.com/showthread.php?tid=5768 Thu, 09 Feb 2012 16:05:12 +0000 admin]]> https://forum.lavalink.com/showthread.php?tid=5768
http://lavalink.com/2012/02/parallel-por...ma-cutter/

In a nutshell:

• strong resistance to electrical noise
  
• robust cabling
  
• positive locking connectors
  
• bi-directionality of the sort needed by servo motors
  

]]>
http://lavalink.com/2012/02/parallel-por...ma-cutter/

In a nutshell:

• strong resistance to electrical noise
  
• robust cabling
  
• positive locking connectors
  
• bi-directionality of the sort needed by servo motors
  

]]> https://forum.lavalink.com/showthread.php?tid=110 Thu, 08 Dec 2011 23:55:20 +0000 Ron Jenkins]]> https://forum.lavalink.com/showthread.php?tid=110
Instead, their corporate office is now equipped with LAVA HQ Plus-126 devices, each monitoring up to 100 store locations, allowing room for expansion on each HQ Plus. Their HQ Plus devices are identified by geographical territory, because Quiznos polls at night when their stores are closed, in various time zones.

The full details are here:
http://www.lavalinknews.info/quiznos-inc...io-part-1/
]]>
Instead, their corporate office is now equipped with LAVA HQ Plus-126 devices, each monitoring up to 100 store locations, allowing room for expansion on each HQ Plus. Their HQ Plus devices are identified by geographical territory, because Quiznos polls at night when their stores are closed, in various time zones.

The full details are here:
http://www.lavalinknews.info/quiznos-inc...io-part-1/
]]> https://forum.lavalink.com/showthread.php?tid=53 Fri, 02 Dec 2011 21:56:13 +0000 mbudds51]]> https://forum.lavalink.com/showthread.php?tid=53
I'm piping the data out of the Serial Port, located on the Motherboard, to the TVs by way of the following command:

type cmdlist.txt >> COM1

I was hoping to get past the distance limitations by connecting to the TVs via Ethernet.

Does anyone know if the ESL is capable to sending data to the Virtual COM ports though batch programming?]]>
I'm piping the data out of the Serial Port, located on the Motherboard, to the TVs by way of the following command:

type cmdlist.txt >> COM1

I was hoping to get past the distance limitations by connecting to the TVs via Ethernet.

Does anyone know if the ESL is capable to sending data to the Virtual COM ports though batch programming?]]>